DIY-KIT-IN-14-Arduino-Shield-NCS314-Nixie-Tubes-Clock-WITH-TUBES-01-uo
in-14

DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES

DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES

DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
IN-14 Nixie Tubes Clock Shield for Arduino UNO/Genuino & Arduino MEGA – NCS314 HW v2.2. The Ardrduino Nixie Tubes Shiled NCS314 allow You to make 6 digits Nixie Tubes Clock in Divergence Meter Mini style (by GRA & AFCH). Or You can just display any 6 digits strings on this IN-14 Nixie Tubes made in xUSSR. Hundreds of thousands of Arduino Boards are already fueling peoples creativity all over the world, everyday. PCB design, schematic, housing and software made by GRA & AFCH. Nixie Clock Shield NCS314 compatible with Arduino UNO/Genuino & Arduino MEGA, so it allows you to write your own unique programs on the Arduino platform, the latest sources are always available on. Github at the NixeTubesShieldNCS314 repository. The base listing c. Only BARE PCB and full set of electronics parts (except Arduino, culumns and power supply). This is example of assembled board NCS314 with full complectation. Bare board to make. Shield NCS314 with soldered Nixie Tubes IN-14 and IN-3 neon lamps. Bare NCS314 board 1pc. IN-14 Nixie Tubes 6pcs. IN-3 Neon lamps 2pcs. Set of electronics parts. Set of hex spacers and screws. User manual on vintage-style paper. This listing does NOT contain the Arduino board and power supply. Flashed Arduino Mega here. IR Remote Controller RM-X153. And upload software into your arduino. Easy to build beautiful clock we offer housing. Easy to customize firmware under Your own needs, thanks to an open platform Arduino. Fast uploading via USB. The latest version of the firmware always available on GitHub. No need to download drivers we are use only Genuine USB to serial converters. Drivers for them pre-installed in all popular OS: Windows, MacOS, Linux. Very high qualty of Printed Circuit Boards. If you have ANY questions. Shiled support 6 IN-14 Nixie tubes [hh:mm:ss]. Full static display mode. Slote Machine (Ani poisoning). Temperature display (DS18B20) [Celsius or Fahrenheit]. GPS time synchronization (requires a standard GPS receiver, NMEA protocol, 5 volt power supply, not included). Operation via IR remote control (Remote control Sony RM-X151, not included). No need refresh or update information on the tubes. The maximum possible brightness of the tubes. Date format: DD:MM:YY. Unique RGB LEDs backlight with 16,7 million colors. Very easy to switch LEDS off/on. As alarm sound clock uses standard RTTTL (Nokia format) melodies, so You can easy change it. (included songs: mission impossible, we wish you). Easy updating firmware via USB using Arduino IDE. Power On Self-Test (POST): LEDs test, tubes test, sound test. Integrated High Voltage Power supply: 150 220V. 3 PWM channels for RGB LEDs 8 bit per channel = 24bit = 16,7 million colors. It can be disabled in the menu (see manual). Test points for testing, adjusting and controlling low and high voltage circuits. RTC (Real Time Clock) High precision time chip DS3231 with Backup battery. Acquiring time via external GPS module (only with Arduino Mega). 3 buttons on board to control. Potenciometer to adjust High Voltage. IR reciver TSOP4836 for IR remote controllers (may conflict with Tone library). 8 pcs of RGB SMD LEDs. SPI up to 4Mhz. Places for 2 column with 2 neon dots inside. Separate controls upper and lower dots. Power consumption: 12V, 760mA. Recommended: 12V, 1-2A (center pin positive +). Nixie Tubes Shiled NCS314 PCB size: 200mm x 53.34mm. (7.87 x 1.2 in). Actual photos of KIT. Arduino Nixie Tubes Clock Shield NCS314 Top View. Arduino Nixie Tubes Clock Shield NCS314 bottom View. Boards Dimensions in 2D and 3D. Nixie Tubes Clock Shield for Arduino NCS314 Photo Gallery. This is example of assembled board NCS314 complete Set. The base listing contains only BARE PCB and full set of electronics parts (Arduino, Columns and Power Supply are EXCLUDED from set). After payments received and verified. The item “DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES” is in sale since Monday, March 13, 2017. This item is in the category “Home & Garden\Home Décor\Clocks\Alarm Clocks & Clock Radios”. The seller is “gra_and_afch_2″ and is located in Dnipropetrovsk. This item can be shipped worldwide.
  • Year Manufactured: 2019
  • Brand: GRA & AFCH
  • Room: Bathroom
  • Model: Divergence Meter
  • Display Type: Nixie Tubes
  • Era: 21st Century (2000-now)
  • Type: Nixie tubes Arduino Shield
  • Style: Vintage/Retro
  • Material: Metal
  • Country/Region of Manufacture: Ukraine
  • Original/Reproduction: Original
  • Power Source: Electrical
  • Movement: Quartz (Battery Powered)
  • MPN: Nixie Clock
  • Color: Blue
  • Features: Alarm

DIY KIT IN-14 Arduino Shield NCS314 Nixie Tubes Clock WITH TUBES
Standard